I also tried connecting the camera directly to my laptop to see if ConfigTool would pick it up, but nope. I factory reset the camera by holding in the reset button for 30 seconds, but that didnt change anything. tar file gzip my-image. docker save my-image:latest > my-image.tar Compress the. Then the IP address can be changed View attachment 43195 Here has a guide. Clieck search setting, and put the right password that you set for the camera. It is also not showing up in Dahuas ConfigTool client. Push the image to Docker Hub and you can get the compressed size of the image on Docker Hub website. type 192.168.1.108 on the webpage to activate the camera firstly, and then use dahua configtool to change the ip address that you need. OpenWindow(0, 0, 0, #W, #H, "", #PB_Window_ScreenCentered | #PB_Window_SystemMenu | #PB_Window_SizeGadget | #PB_Window_MinimizeGadget | #PB_Window_MaximizeGadget) However, when I look at DHCP client list the camera is not showing up. SHGetFileInfo_(PeekS(*memBuffer), 0, SizeOf(SHFILEINFO), #SHGFI_ADDOVERLAYS | #SHGFI_ICON | #SHGFI_SMALLICON)ĭeleteFile(GetTemporaryDirectory() cTempFile ) For capturing license plates, the camera should be mounted lower at about 3 to 5 feet. fetch the information about that executable. Dahua cameras come in several different form factors: Bullet Dome Eyeball Box Wedge Fisheye For identification of faces or fine details, the camera should be mounted between 9ft and 12ft from the ground. If FindExecutable_(cTempFile,GetTemporaryDirectory(),*memBuffer) > 32 var imageSize Float (imageData.length) var image UIImage (data: imageData) var jpegSize UIImageJPEGRepresentation (image, 1) var pngSize UIImagePNGRepresentation (image) var pixelsMultiplied asset.pixelHeight asset.pixelWidth println ('regular data: \ (imageSize) JPEG Size: \ (jpegSize.length) PNG Size: \ (pngSize. Push the image to Docker Hub and you can get the compressed size of the image on Docker Hub website. get the executable releated to the extension Create a blank file - the file's existance is required for FindExecutable()ĬloseFile(OpenFile(#PB_Any, GetTemporaryDirectory() cTempFile )) For each image, LoadImage () followed by ImageHeight (), ImageWidth () and ImageDepth () (if necessary, not sure what you mean by 'format' - it can only be a bitmap). Until FileSize( GetTemporaryDirectory() cTempFile cExtension ) = -1 You will need to parse all the icon images in the file (use -1 as the last value of ExtractIcon to get the image total). If Left(cExtension,1)"." : cExtension = "." cExtension : EndIf This camera is on the larger size, with an overall length of 244mm (9. Just check that we have a dot in the extension. Monitor is incapable of displaying the device recorders resolution output.Code: Select all #SHGFI_ADDOVERLAYS = $20 If the current setup is 1920*1080, then you need to set the monitor resolution as 1920*1080 or 1080P capable.ġ1. On the monitor check the current resolution setup. If a DP connection, make sure the monitor is at least 1080p.ġ0. For the HDMI connection, less than 50 feet is highly recommended with 25 feet or less is preferred.ĩ. If a HDMI connection, 1080p monitor is recommended.Ĩ. For the DVI connection, Up to 15 feet at high resolutions (above 1280x1024), or up to 50 feet at lower resolutions (1280x1024 and below)ħ. I would go back to H.264 ( ) for compression to see if that makes any difference. So, if FPS is set to 25 which is rather high, then I-Frame should also be 25. If a DVI connection, also ensure the screws are tight.Ħ. One of the most obvious problems from your settings is 'i frame interval'. For the VGA connection, 25 feet or less is recommended for high resolution and 50 feet for lower resolution.ĥ. If a VGA connection, ensure the screws are tight.Ĥ. New issue Cannot get image dimensions 6755 Closed bloodyburger opened this issue on 3 comments bloodyburger commented on OS: Debian Virtualization: Docker Clients: Mobile iOS Browser: Firefox 93 Jellyfin Version: 10.7. Check your physical connections from the system to the monitor.ģ. I am unable to test the HIK because I am having trouble getting into the interface. I went into all of them except the HIK and none of the Amcrests or the Dahua can send test e-mails. The displayed video is not full in the monitor.ġ. My current cam fleet is the new outdoor POE Dahua, an outdoor HIK POE, an indoor Amcrest POE and 2 Amcrest wifis.
0 Comments
Leave a Reply. |